s235jrc steel thickness

32 Comments

s235jrc steel thickness

12345Next200 mm
Newly rolled and cut S235JR steel plate S235JR (+N) is a non-alloy structural steel.We have large quantities of S235JR in stock with thicknesses up to 200 mm.The minimum thickness is normally 5 mmS235JR Steel Plates

The tables below show the mechanical properties of grade S235JR Minimum yield strength Reh MPa Tensile strength Rm MPa Minimum elongation A Lo = 5,65 * So (%) Notch impact test Steel grade Nominal thickness mm Nominal thickness mm Nominal thickness mm Temperature Min.absorbed energy 16 >16 40 >40 63 >63 80 >80 100 >100 125 >3 100 >100 125 >3 40 >40 63 >63 100Bright steel delivery program - BlankstahlS235JRC+C S355J2C+C C15+C C35+C C45+C 11SMn30+C 11SMnPb30+C Diameter d (mm) 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36

EN 10025 Grade S235JR as-rolled condition (+AR) - Low

S235JR is applicated for construction parts of moderate strength load,which are not liable to inspection.Max.product thickness accounts for 25 mm.For this steel are available (see material No.1.0120 acc.to DIN EN 10025) grades for - folding (KQ)-S235JRC - cold forming of sections (KP)-S235JRC - cold drawing (KZ)-S235JRCEN 10025 Grade S235JRC as-rolled condition (+AR) - Low S235JRC is applicated for moderately loaded construction parts that are not liable to inspection as folding,section cold forming and cold drawing grades.Max.product thickness amounts 20 mm for folding and 8 mm for cold roll forming grades.EN 10025-2 S235JR high strength structural steel plate Henan Gang Iron and Steel Co.Ltd( BBNSTEEL) is specialized in low alloy high strength structural steel,mainly dealing with .specification standard plates in EN 10025-2,EN 10025-3,EN 10025-4,EN 10025-6,ASTM A633,ASTM A573,ASTM A572,.DIN 17100,JIS G3106,ASTM A709,ASTM A283,ASTM A529,ASTM A656,EN 10225,ISO 630,NFA 35-501,and so on,the thickness up to 300mm.

FREE CUTTING STEELS - Trafileria Mauri

High machinability steel not destined to heat (W.NR.1.0715) CHEMICAL COMPOSITION (heat analysis according to the EN 10277-3 standard) *MECHANICAL FEATURES (according to the EN 10277-3 standard) Thickness mm rolled + peeled rolled (+SH ) Cold drawn ( +C ) HB hardness Rm (MPa) Rp 0,2 minimum values (MPa) Rm (MPa) A 5 % minimumGeneral Engineering SteelDESCRIPTION Mild steel Mild steel Carbon steel Carbon steel Fine grained Fine grained Fine grained Replacing BS 040-060A10-12 080M36 DIN St 37-2 K St 52-3 K St 50-2 K Ck 35 K Dimensions mm 5 - 100 5 - 100 5 - 80 5 - 80 Thickness mm 5 - 50 Tolerance ISO h11 %C max 0,17 max 0,20 0,32 - 0,39 %Si 0,15 - 0,30 0,15 - 0,30 max 0,40 ManusteelcnChina steel suppliers - Superior technology Technological properties of grade steel S235JRC Hardness and heat treatment specification of steel grade S235JRC to steel thickness (a) multiples said.(2) in the ASTM A6 standard specified scope can meet any additional conditions.(3) from the standard for 50 mm (2 in).

S235JR / 1.0038(dubl) - SteelNumber - European Steel and

Chemical composition % of steel S235JR (1.0038 (dubl)) EN 10025-2-2004 Nominal thickness =< 40 (mm) C max = 0.17 Nominal thickness =< 40 (mm) CEV max = 0.35 New opportunities for buyers!S235JR ST37-2 E24-2 SS400 A283C A36 Steel plate,S235JR S235JR steel is a type of steel sheet under EN standard which is used to build ship,bridge.A36 steel is carbon steel plate.S235JR is equivalent to DIN:St37-2,etc.If you need S235JR steel,ss400 ASTM A36 steel,please contact us.S235JR steel - Steel gradesTool Die Steels Inc.Stainless Steel,Special Steel,Compressor Blading,Turbine Blading,Superalloy Supplier.S235JR Round Bar S235JR Flat Bar S235JR Hollow Bar S235JR Tube / Pipe S235JR Sheet / Plate S235JR Strip / Coil S235JR Wire S235JR Forging S235JR Tube / Pipe TEL:+86-13880247006

S235jrc,chemical composition of steel s235jrc (1

Translate this pageg and cold drawing grades.Max.product thickness amounts 20 mm for folding and 8 mm for cold roll.1.0122 Steel S235JRC+C,S235JR+AR,S235JR+N.S235JRCS275JRC - Salzgitter Flachstahl GmbHequal the product thickness if the latter is between 5 and 0 mm.The tests are performed by using samples similar to Charpy-V samples.The values specified in the table above are to be reduced proportionally to the sample width.Usage These general structural steel grades are characterised by a minimum yield strength of 85360 N/mm2 SSAB Domex 240YP - meets S235JRC - SSABTypical applications include a wide range of fabricated components and steel structures.SSAB Domex&240YP meets or exceeds the requirements of S235JRC,S235J0C or S235J2C in EN 10025-2,depending on agreed impact strength requirements at the time of order.Upon agreement,it can be delivered double certified and CE marked.

Steel Primapol

Steel Carbon and alloy construction steel Company Primapol is newly offering Carbon and alloy construction steel.We keep stock from Cold forming steel,material which allow our customer to reduce cost of machining.S 235 JR Range of goods round bars,length 3000 6000 mm,version []

Comments

Leave a Message

Copyright © 2020.Ezir All rights reserved.